Mechatronic systems I : applications in transport, logistics, diagnostics and control /
Waldemar Wójcik, Sergii Pavlov, and Maksat Kalimoldayev.
Bok Engelsk 2021 · Electronic books.
| Medvirkende | |
|---|---|
| Omfang | 1 online resource (307 pages)
|
| Utgave | First edition.
|
| Opplysninger | Cover -- Half Title -- Title Page -- Copyright Page -- Table of Contents -- List of contributors -- 1 Method of project calculation of hydroimpulsive device for vibroturning with an incorporated cycle spring pressure pulse generator -- 1.1 Introduction -- 1.2 Materials and results of research -- 1.3 Conclusion -- References -- 2 Determination of the optimal parameters of the driver of a resonance vibratory stand for diagnostics of dampers -- 2.1 Introduction -- 2.2 Analysis of literary sources and statement of the problem -- 2.3 Purpose and tasks of the research -- 2.4 Materials and methods -- 2.5 Results and discussion -- 2.6 Conclusion -- References -- 3 Algorithm to calculate work tools of machines for performance in extreme working conditions -- 3.1 Introduction -- 3.2 Analysis of destroyed buildings and structures -- 3.3 Materials and methods -- 3.4 Results and discussion -- 3.5 Conclusion -- References -- 4 Vibration diagnostic of wear for cylinder-piston couples of pumps of a radial piston hydromachine -- 4.1 Introduction -- 4.2 Analysis of dynamical processes in RPH with spherical ball pistons -- 4.3 Dynamical model of radial piston pump with HVT -- 4.4 Diagnostics algorithm for pressure surges of cylinder and piston pumpcouples of RPH -- 4.5 Diagnostics algorithm for a statistical vibration signal -- 4.6 Calculation and experimental research -- 4.7 Conclusion -- References -- 5 Mathematical modeling of dynamic processes in the turning mechanism of the tracked machine with hydrovolume transmission -- 5.1 Introduction -- 5.2 Analysis of research methods of dynamic processes of power transmissions in vehicles with HVT -- 5.3 Mathematical models of transient regimes in the turning mechanism of a tracked vehicle with the HVT -- 5.4 Experimental and calculation research on choice of parameters of turning mechanism with HVT -- 5.5 Conclusions.. - 12 Optimization of design parameters of a counterbalance valve for a hydraulic drive invariant to reversal loads -- 12.1 Introduction -- 12.2 Analysis of the literary sources of hydraulic drives with counterbalance valves -- 12.3 Materials and methods of studying the hydraulic drives invariant to alternating loads -- 12.4 Results and discussion -- 12.5 Conclusion -- References -- 13 Calculations of unsteady processes in channels of a hydraulic drive -- 13.1 Introduction -- 13.2 Analysis of features and varieties of channels of hydraulic drive types -- 13.3 Materials and methods of studying the nonstationary processes in channels of the hydraulic drive -- 13.4 Conclusion -- References -- 14 Analysis, development, and modeling of new automation system for production of permeable materials from machining waste -- 14.1 Introduction -- 14.2 Research and analysis of the method of producing PPMs -- 14.3 Development of processing technology with use of machining waste -- 14.3.1 Main powder properties -- 14.3.2 Dry radial isostatic pressing (DRIP) of PPMs -- 14.3.3 Sintering of the PPM -- 14.3.4 Properties of PPM -- 14.4 Results and discussion -- 14.5 Conclusion -- References -- 15 Study of effect of motor vehicle braking system design on emergency braking efficiency -- 15.1 Introduction -- 15.2 Analysis of motor vehicle braking system design specifics and of theoretical premises for assessment of functionality of such braking systems -- 15.3 Results of field research on motor vehicle braking system efficiency in case of emergency braking -- 15.4 Recommendations for upgrading existing approaches to assessment of motor vehicle braking efficiency in the course of accident-related automotive equipment expert examination -- 15.5 Conclusions -- References -- 16 Essential aspects of regional motor transport system development -- 16.1 Introduction.. - 16.2 Functional analysis of regional MT systems -- 16.3 Aspect of regional MT system development associated with the use of intelligent tyres -- 16.4 Specifics of intelligent tyres -- 16.5 Conclusion -- References -- 17 Improvement of logistics of agricultural machinery transportation technologies -- 17.1 Introduction -- 17.2 Literature review -- 17.3 Research objectives -- 17.4 Statement of basic materials -- 17.5 Conclusion -- References -- 18 Optimization of public transport schedule on duplicating stretches -- 18.1 Introduction -- 18.2 Review of scheduling methodology -- 18.3 Scheduling methodology of route vehicle on duplicating stretches -- 18.4 Application -- 18.5 Conclusion -- References -- 19 Dynamic properties of symmetric and asymmetric layered materials in a high-speed engine -- 19.1 Introduction -- 19.2 Beam modelling -- 19.3 Layered asymmetric plate -- 19.4 FGM beam -- 19.4.1 Symmetric beam -- 19.4.2 Asymmetric beam -- 19.4.3 Comparison of functionally graded and three-layered plates -- 19.5 Discussion -- 19.6 Conclusion -- References -- 20 Selection and reasoning of the bus rapid transit component scheme of huge capacity -- 20.1 Introduction -- 20.2 Research results -- 20.3 Recommendations -- 20.4 Conclusion -- References -- 21 Physical-mathematical modelling of the process of infrared drying of rape with vibration transport of products -- 21.1 Introduction -- 21.2 Literature review and problem statement -- 21.3 Aim, objective, material and methods -- 21.4 Results and discussion -- 21.5 Conclusion -- References -- 22 Energy efficiency of gear differentials in devices for speed change control through a carrier -- 22.1 Introduction -- 22.2 Analysis of the general method of PE determination of gear differentials.. - 22.3 Materials and methods for determining of the energy efficiency of gear differentials with closed circuit hydrosystems of speed control devices through PE evaluation -- 22.4 Discussion of the results of the determination of the PE of gear differentials of speed change devices through a carrier with two internal or external engagements -- 22.5 Conclusion -- References -- 23 Influence of electrohydraulic controller parameters on the dynamic characteristics of a hydrosystem with adjustable pump -- 23.1 Introduction -- 23.2 Problem setting -- 23.3 Study object and research methodology -- 23.4 Conclusion -- References -- 24 High-precision ultrasonic method for determining the distance between garbage truck and waste bin -- 24.1 Introduction -- 24.2 Methods -- 24.3 Main results of the research -- 24.4 Results of experiments -- 24.5 Conclusion -- References.. - References -- 6 Forecasting reliability of use of gas-transmitting units on gas transport systems -- 6.1 Introduction -- 6.2 Analysis of the problem -- 6.3 Materials and methods of studying -- 6.4 Results and discussion -- 6.5 Conclusions -- References -- 7 Development of main gas pipeline deepening method for prevention of external effects -- 7.1 Introduction -- 7.2 Analysis of the methods and materials -- 7.3 Results and discussion -- 7.4 Conclusion -- References -- 8 Increasing surface wear resistance of engines by nanosized carbohydrate clusters when using ethanol motor fuels -- 8.1 Introduction -- 8.2 Analysis of the literature sources -- 8.3 Materials and methods used in the study -- 8.4 Results and discussion -- 8.5 Conclusion -- References -- 9 Method of experimental research of steering control unit of hydrostatic steering control systems and stands for their realization -- 9.1 Introduction -- 9.2 Analysis of literary data and problem statement -- 9.3 Purpose and objectives of the research -- 9.4 Materials and methods of research -- 9.5 Conclusion -- References -- 10 Possibility of improving the dynamic characteristics of an adaptive mechatronic hydraulic drive -- 10.1 Introduction -- 10.2 Analysis of the results of investigations of mechatronic hydraulic drives -- 10.3 Object and method of research -- 10.4 Research results of mechatronic hydraulic drive -- 10.5 Conclusions -- References -- 11 Application of feedback elements in proportional electrohydraulic directional control valve with independent flows control -- 11.1 Introduction -- 11.2 Literature review and proposed solutions -- 11.3 Materials and methods of studying processes in directional control valve with independent flows control -- 11.4 Results and discussion -- 11.5 Conclusion -- References.. - The subject of this first volume of a two-volume set are the issues related to the components and systems of transport machines. Tests of motor vehicle systems are described: suspension dampers, steering, brakes, differentials. Design issues of machine elements operating in extreme conditions are also addressed. The possibility of increasing wear resistance in high-speed and ethanol-powered engines is analyzed. An extensive part covers the dynamics of hydraulic, electro-hydraulic and mechanical-hydraulic systems and the issues of diagnostics and automatic control in such systems. Aspects of the regional system of motor transport, public transport and transport and logistics of agricultural machinery are also addressed. The volume also examines selected technical and economic issues of gas transport. Topics of modelling of production processes with the transport of products are a complement.
|
| Emner | |
| Sjanger | |
| Dewey | |
| ISBN | 1-000-48729-6. - 1-000-48731-8. - 1-003-22413-X
|
