HAMILTON STANDARD ENGINE ELECTRONICK CONTROL - COMPONENT MAINTENANCE MANUAL WITH IPL 73-21-13/SERVICE BULLETIN ENGINE FUEL AND CONTROL EEC118-11-73-XX : and FUEL CONTROL COMPONENT MAINTENANCE MANUAL WITH IPL 73-21-41/SERVICE BULLETIN ENGINE FUEL AND CONTROL JFC118-11-73-XX
Bok Engelsk
| Medvirkende | |
|---|---|
| Utgitt | Ontario : Hamilton Standard
|
| Opplysninger | There are 4 individual manuals in this binder. The first one is published Oct 15/83. Last Revision; Revision No. 4, Issue Date: February 15/93. The second one has no publishing date. The third one is published April 1/85, Last Revision; Revision No. 2 Issue Date: Aug 15/91. And the fourth has no publishing date.. - TABLE OF CONTENTS: (ENGINE ELECTRONIC CONTROL, CMM WITH IPL) INTRODUCTION Scope Arrangement of Manual and Usage Description and Operation Testing and Troubleshooting Disassembly, Cleaning, Check, Repair, and Assembly Illustrated Parts List Leading Particulars Cooling Physical Dimensions Power Input Requirements Verification Nameplate Abbreviations DESCRIPTION AND OPERATIONS System Description EEC Physical Description EEC Operation Input Conditioners DC Voltage Inputs General Reference Protection Voltages Potentiometer Excitation PLA Potentiometer Signal PO Ambient Pressure Signal PO Sensor Bias (Zero Calibration) and Gain (Full Scale Calibration) Compensation ^P Differential Pressure Signal ^P Sensor, Bias (Zero Calibration) and Gain (Full Scale ^P Calibration) Compensation TO Ambient Temperature Signal Drift Signals Q Bug Reference Input Torque Motor Current Sense A/D Converter A/D Conversion Speed Inputs General NH Speed Measurment NPT Speed Measurment Discrete Inputs General Engine Trim/Test Trim (1-3) Rating Trim (1 and 2)/Test Trim (4 and 5) Ground Test Take-off Reduce Power Rating Logic Bits (1 and 2) NH Overspeed Test Reversion Mode Arm Propeller Governor Uptrim Feather Microprocessor General Data Bus Buffers Programmable Read Only Memory (PROM) Random Access Memory (RAM) Control Multiplexer NH Overspeed Detector NH Underspeed Detector Output Interface Torque Motor Output High Side Switch Torque Meter Bug Output EEC Fault Indicator Output Reversion Mode Relay Output Serial Display Built-In-Test General PROM Sum Check RAM Test Foreground/Background Health Test Interface Flag Check Instruction Test Range Test Test Voltage Watchdog Timer Loss of Clock Detector Power Supply General Operation Power Input and Effector Supply Pulse Width Regulation Protection Circuits +5V Overvoltage +28V Undervoltage Transformer Overcurrent +12V Supplay -12V Supplay +5V Supplay PSR Generator Microcircuits TESTING AND TROUBLESHOOTING Introduction Functional Bench Test General Required Equipment Signal Definitions Input Signals RAM Address Signals Output Signals Test Procedures Initial Conditions Preliminary Tests Input Power EEC Current Check Correction Factor (C. F.) RAM Readout Check Funcitonal Test Thermal Cycle Test General Required Test Equipment Signal Definitions Input Signals Output Signals Test Procedures Vibration Test General Required Test Equipment Signal Definitions Input Signals Output Signals Test Procedures Troubleshooting General Information Reversion and Fault Flag Decode Maintenance Word Schematic References Digital Microcircuit References DISASSEMBLY General Disassembly Cover Removal Digital Board Assembly Removal Analog Board Assembly Removal Pressure Transducer Removal Connector Module Removal CLEANING General External Cleaning Internal Cleaning CHECK General Visually Inspect Board Assembly Visually Inspect Chassis and Mechanical Assemblies REPAIR-GENERAL General Materials and Tools ASSEMBLY General Assembly J1 Connector Module Installation Pressure Transducer Installation Analog Board Assembly Installation Digital Board Assembly Installation Storage Instructions End Assembly Subassemblies and Components FITS AND CLEARANCES General SPECIAL TOOLS, FIXTURES AND EQUIPMENT General ILLUSTRATED PARTS LIST Introduction Purpose Configuration Control Item Number and Variants in the Detailed Parts List Configuration Changes Codes Configuration Changes Summary Parts Listing Procedures Part Numbers Effectivity Codes Abbreviations and Symbols Electrical/Electronic Component Parts List Using an Electrical/Electronic Component Parts List Electronics Parts Wich Require Special Handling Provisioning Parts List Procedures Identification of Current Parts List Changes Material Information Table Vendor Codes Equipment Designator Index Numerical Index Detailed Parts List Figure 1 - Engine Electronic Control Figure 2 - Digital Board Assembly Figure 3 - Digital Board Assembly, Component Side Figure 4 - Digital Board Assembly, Solder Side Figure 5 - Analog Board Assembly Figure 6 - Analog Board Assembly, Component Side Figure 7 - High Side Switch Board Assembly Configuration Change Summary NO. 2 HAS NO TABLE OF CONTENTS FUEL CONTROL, CMM WITH IPL Introduction Description and Operation Description Operation Testing and Troubleshooting Test Conditions Symbols and Abbreviations Required Equipment Preparation of Fuel Control for Test Preliminary Control Setup and Adjustment Final Calibration and Recording of Test Data Post Test Requirements Troubleshooting - Control Calibration Disassembly General Instructions Turbine Type Engine Fuel Control Application Housing Group Main Housing Group, Part 1 Main Housing Group, Part 2 Main Housing Group, Part 3 Application Housing and Inserts Housing and Valve Cleaning General Cleaning Requirements Specific Cleaning Requirements Check General Requirements Nondestructive Test Data Repair-General General Steel Parts Aluminum Parts Rubber Parts Dowel-Type Straight Pins Screw Thread Inserts Woodruff Keys Specific Repair Assembly General Assembly Procedures Housing and Valve Application Housing and Inserts Main Housing Group, Part 3 Main Housing Group, Part 2 Main Housing Group, Part 1 Application Housing Group Turbin Type Engine Fuel Control Storage After Assembly Fits and Clearances Sliding Fits Springs Assembly Torque Valves Special Tools, Fixtures and Equipment Illustrated Parts List NO. 4 HAS NO TABLE OF CONTENTS
|
| Emner | |
| Dewey |
