The Grouting Handbook : A Step-by-Step Guide to Heavy Equipment Grouting
Donald M. Harrison
Bok Engelsk 2000 · Electronic books.
| Utgitt | Burlington : : Elsevier Science, , 2000.
|
|---|---|
| Omfang | 1 online resource (193 p.)
|
| Opplysninger | Description based upon print version of record.. - Front Cover; The Grouting Handbook; Copyright Page; Contents; Preface; Chapter 1. The Foundation; The Initial Machinery Foundation Design; Reciprocating Compressor and Engine Foundations; Skid-Mounted Equipment Foundations; Foundations for Centrifugal Pumps; Foundation Mass to Equipment Weight Ratio for Pumps; Soil Conditions; Concrete for the Foundation; Adding Water to the Concrete Mix at the Job Site; The Concrete Mix; Placing Concrete in Hot Weather; Pouring Concrete in Cold Weather; Concrete Curing for Machinery Foundations; Methods for Curing Concrete; Types of Portland Cement. - Contamination of the FoundationGuidelines for Use of Epoxy Grout on Oil-Saturated Concrete; The Acceptable Moisture Content in Concrete, or How Soon Can We Pour the Epoxy Grout on the New Concrete?; Chapter 2. Anchor Bolts; The Basics of Anchor Bolts; Measuring Equipment Pull-Down at the Anchor Bolts; Determination of Anchor Bolt Pullout Strengths; Machinery Reliability Starts with the Anchor Bolts; How Anchor Bolts Behave; Conventional Procedures for Achieving Initial Anchor Bolt Tension; Types of Material Normally Used for Anchor Bolts of 1-11/2 in. in Diameter. - General Installation Procedures for Epoxy GroutConcrete Temperature; Ambient Temperature and Its Effect on Epoxy Grout; Epoxy Grouting in Cold Weather; Epoxy Grouting in Hot Weather; Epoxy Grout Flow versus Clearance; Chapter 5. Selecting an Epoxy Grout; Chapter 6. The Use of Rebar and Expansion Joints in Epoxy Grout; Edgelifting: Cause and Cure; Why and When To Use Expansion Joints in Epoxy Grout; Suggested Expansion Joint Locations and Basic Construction Material; The Secondary Seal; The Primary Seal; Mixing Elastomeric Epoxy Expansion Joint Compound and Sand. - Merits of Epoxy Grouts versus Cement GroutsCementious Grouts: Cement Grouting in Real Life; Concrete Surface Preparation; Temperature; Mixing Cement Grout; Placing and Curing; Cement Grouting in Hot Weather; Recommended Temperature Guidelines for Hot Weather; When Cooling Cannot Be Accomplished; Cement Grouting in Cold Weather; Recommended Temperature Guidelines for Cold Weather; Chapter 4. Epoxy Grout; An Introduction to Epoxies; The Chemistry of Epoxy Grout; General Characteristics of Epoxy Grouts; Terminology; ASTM C 1181 Calls for; Conclusion. - Other Methods for Expansion Joint Design. - Typical Ways of Applying, or Measuring, Anchor Bolt Preload or TensionSeven Possible Causes of Loss of Preload in Anchor Bolts; Bolt Tensioning Devices Currently Available; The Easy Way To Observe and Monitor Anchor Bolt Preload, Both Initial and Residual; Load-Generating Washers; Ultimate Systems; Conclusion; Proper Anchor Bolt Tensioning; The Following Are Rules of Thumb for Anchor Bolt Tensioning; ""Is It Safer to Over-Tighten an Anchor Bolt Than To Under-Tighten It?""; Chapter 3. Cement Grout; A Comparison between Epoxy and Cement Grouts, or Which Product Should We Use?; Conclusion. - Based on twenty years of research and field experience, this book collects a vast amount of information into a handy reference for mechanical and civil engineers. It focuses on four basic elements of grouting: load carrying capability of the foundation soil; mass design, concrete mix and installation, and curing procedures of the foundation; anchor bolts; and the grout. From the ground up, this book takes you step by step through the grouting process. Clear, straightforward directions give you details on preparing the foundation and surface, and selecting the best material and method. Comprehe
|
| Emner | |
| Sjanger | |
| Dewey | |
| ISBN | 088415887X
|
